How to measure resistance between L1-bridges? -1

» Welcome to English «

New topic Answer

Lupson
offline

OC Newbie
21 Jahre dabei !

Hi everyone,

about a month ago I bought a AMD T-bred A 1800+ for my old Abit KT7-RAID Mb. After cutting all L1 bridges and two L3 bridges (to get 16.5x multi) it worked flawlessy for 4 days @ 105*16.5 Mhz. Then one morning it just refused to post. The evening before, it froze when I shut it down with the "Windows XP is shutting down" screen. I just pressed the power button for four seconds to shut the system off.

The system works just fine with my old 750 Mhz T-bird so the rest of the system isn't faulty. My theory is that one of my L1-bridges somehow has shorted again due to heatsink pressure or heat. (It didn't post at all until I had cut all L1-brides). I've tried various stuff the last few weeks, like resetting CMOS, pressing the reset button xx-times a.s.o.

Now that I've explained the background story - my plan is to use a multimeter this weekend and measure the resistance between the L1-bridges. My theory is that if any of the (presumably) cut bridges show low or nonexistant resistence, it isn't cut and I can cut a bit more with my scalpel until the resistance gets really high (i.e. - cut). Then try booting up again.

Do you processor surgeons think this is a plausible method to "repair" my poor T-bred? If anyone feel like explaining thorughly - where to place the measuring points, what values can be expected a.s.o. it would be really appreciated.

Regards,
Lupson

Beiträge gesamt: 15 | Durchschnitt: 0 Postings pro Tag
Registrierung: Jan. 2003 | Dabei seit: 7989 Tagen | Erstellt: 18:49 am 19. Feb. 2003

zelan
offline

Basic OC
21 Jahre dabei !

Intel Pentium IV
2400 MHz @ 3185 MHz
34°C mit 1.55 Volt

You can try to measure the resistance between the bridges. But I'm not sure how big the resistance may be. I would try to use the "continuity test" (don't know if that's the right word). This is a symbol in the resistance field. It looks like a cross with triangle over it. Just like the sign for a diode in a circuit diagram (I think). If there is a pass in the bridge the multimeter makes a noise. If there 's no pass, nothing happens. So you can make sure if the bridge is closed or not (Sound -> Bridge isn't cut; No sound -> Bridge is cut).

(I hope you know what I want to say...)

Beiträge gesamt: 150 | Durchschnitt: 0 Postings pro Tag
Registrierung: Feb. 2003 | Dabei seit: 7964 Tagen | Erstellt: 0:08 am 20. Feb. 2003

Lupson offline OC Newbie 21 Jahre dabei !	Thank you for your answer! I'll try this approach and I'll post the results here. /Lupson
	Beiträge gesamt: 15 \| Durchschnitt: 0 Postings pro Tag Registrierung: Jan. 2003 \| Dabei seit: 7989 Tagen \| Erstellt: 17:02 am 20. Feb. 2003

Lupson
offline

OC Newbie
21 Jahre dabei !

Okey, here goes: All L1-bridges were cut, but the middle L3-bridge - which was supposed to be connected, wasn't connected. That is certainly due to the fact that I slipped with the razor once and cut a little bit on it by mistake. With all L3 bridges cut the multiplier is 18.5x. With my 100 Mhz FSB speed it would be 1850 Mhz on an 1800+, which may be above what it can post on. It worked fine (but hot) on 1733 mhz, but hopefully this is why it isn't posting. I'll get some silver paint and repair the bridge and then I'll tell you how it went!

Zelan - Your method worked perfectly - beep - contact. no beep - no contact!

/Lupson

Beiträge gesamt: 15 | Durchschnitt: 0 Postings pro Tag
Registrierung: Jan. 2003 | Dabei seit: 7989 Tagen | Erstellt: 21:10 am 23. Feb. 2003

zelan offline Basic OC 21 Jahre dabei ! Intel Pentium IV 2400 MHz @ 3185 MHz 34°C mit 1.55 Volt	Good to here that. But why only 100MHz FSB?
	Beiträge gesamt: 150 \| Durchschnitt: 0 Postings pro Tag Registrierung: Feb. 2003 \| Dabei seit: 7964 Tagen \| Erstellt: 10:33 am 24. Feb. 2003

Lupson offline OC Newbie 21 Jahre dabei !	It's an old Abit KT7-RAID, based on the VIA KT133 Chipset. Despite its name, it only supports 100 Mhz FSB, though one can OC it to about 105 Mhz without stability issues. Later there were the KT133A chipset and the Abit KT7A MB which had full 133 Mhz FSB support. /Lupson
	Beiträge gesamt: 15 \| Durchschnitt: 0 Postings pro Tag Registrierung: Jan. 2003 \| Dabei seit: 7989 Tagen \| Erstellt: 12:54 am 24. Feb. 2003

Lupson offline OC Newbie 21 Jahre dabei !	Wheeeehoooohooo!!! I fixed the broken bridge with a carbide(?) pen. (Normal writing pen, not an inkl pen). And it posted right away at 16.5*100 Mhz. Now let's tweak it some Thanks! /Lupson
	Beiträge gesamt: 15 \| Durchschnitt: 0 Postings pro Tag Registrierung: Jan. 2003 \| Dabei seit: 7989 Tagen \| Erstellt: 14:14 am 24. Feb. 2003

zelan offline Basic OC 21 Jahre dabei ! Intel Pentium IV 2400 MHz @ 3185 MHz 34°C mit 1.55 Volt	Happy tweaking! By the way, where are you from?
	Beiträge gesamt: 150 \| Durchschnitt: 0 Postings pro Tag Registrierung: Feb. 2003 \| Dabei seit: 7964 Tagen \| Erstellt: 21:31 am 24. Feb. 2003

Lupson offline OC Newbie 21 Jahre dabei !	It's running 100% stably at 1701 Mhz (103*16.5) at 40 deg. Good enough for me. I'm from Sweden BTW. /Lupson
	Beiträge gesamt: 15 \| Durchschnitt: 0 Postings pro Tag Registrierung: Jan. 2003 \| Dabei seit: 7989 Tagen \| Erstellt: 21:43 am 24. Feb. 2003

New topic Answer