No power with USB Ultra IR receiver? -1

» Welcome to English «

New topic Answer

DrJones
offline

OC Newbie
16 Jahre dabei !

AMD Phenom
2500 MHz @ 2500 MHz
48°C mit 1.3 Volt

I installed LEDs on my circuit so I could test without the driver (mainly the power circuit), but I'm not getting anywhere...

I have a red LED hooked up alongside the receiver (TSOP 1738), and a green LED hooked up alongside the optocoupler (CNY17-2). When I press buttons on any remote, the red LED blinks, which I would assume is a good indicator that the device has power and that it's receiving IR signals. However, even when I program my universal remotes to any of the provided Philips codes, the green LED never blinks and my computer never turns off.

I assume that even if I had something hooked up wrong to the computer's power button, the green LED should blink (since it's hooked up on the "inside" of the optocoupler)? I currently have the anode (positive) of the LED connected to pin 1 of the optocoupler and the cathode to pin 2... that's correct, right?

Any ideas?

Beiträge gesamt: 5 | Durchschnitt: 0 Postings pro Tag
Registrierung: Mai 2008 | Dabei seit: 6039 Tagen | Erstellt: 3:51 am 18. Mai 2008

ocinside
aus Krefeld
online

Administrator
23 Jahre dabei !

Intel Core i9
3600 MHz @ 5200 MHz
78°C mit 1.552 Volt

There're a few reasons for this problem.
If you've already tried several philips remote codes and if you've soldered the low current LED with approx. 390 Ohm - 1K resistor to these pins (depends on the LED used), it should light up on the second remote signal.
First of all I would suggest, that you mail or post a picture of the upper and bottom PCB surface with activated macro function.
(with "macro function" I mean the flower symbol on your digital camera).

Hardware News lesen * Talk * Smarthome und Gadgets
Overclock, Modding und Testberichte * Fanartikel kaufen

Beiträge gesamt: 170945 | Durchschnitt: 20 Postings pro Tag
Registrierung: April 2001 | Dabei seit: 8613 Tagen | Erstellt: 19:31 am 18. Mai 2008

DrJones
offline

OC Newbie
16 Jahre dabei !

AMD Phenom
2500 MHz @ 2500 MHz
48°C mit 1.3 Volt

Here you go... shown are the 512x384 thumbnails. Use a link to view the larger versions; I've posted both the untouched pictures and pictures with numbers added so it's easier to coordinate the holes and components. I've got a list of components at the bottom as well.

Thanks for your help!

1024x768 (with numbers)
2048x1536 (with numbers)

1024x768 (with numbers)
2048x1536 (with numbers)

1,2: Qz1
3-10: AT90S 2323-10
11-18: AT90S 2343
19,20: Jumper wire
21,24: Jumper wire
22,23: R3 - 2x ~190W in series
25,26+: LED1
27,28: Jumper wire
29,30: R2 - 390W
31,32: J3
33,34+: C1
35: DATA+
36: DATA-
37,38: Jumper wire
39,40: R1 - 1.5kW
41,42: C2 (marked C3 on LED schematic?)
43-48: CNY17-2
49+,50: LED2
51,52: R4 - 2x ~190W in series
53: VCC
54: GND
55-57: TSOP 1738
58,59: Power Switch

Beiträge gesamt: 5 | Durchschnitt: 0 Postings pro Tag
Registrierung: Mai 2008 | Dabei seit: 6039 Tagen | Erstellt: 3:04 am 19. Mai 2008

ocinside
aus Krefeld
online

Administrator
23 Jahre dabei !

Intel Core i9
3600 MHz @ 5200 MHz
78°C mit 1.552 Volt

Looks very nice, except the two LEDs.
Because they look like bright/ultrabright LED and doesn't look like a low current LED.
This could be the reason, why your Power on/off function doesn't work.
Because it's possible that the Tiny13 IC doesn't get a capable signal from the TSOP and/or the optocoupler doesn't get enough power from the Tiny13 IC (or in the worst case damage the IC output).

So in the first step I would suggest, that you replace the bottom LED with an usual (non-bright) or best with a low current LED.
If you like to use an usual LED, you should connect it in row with the resistor between pin4 (GND) and pin3 (second signal output

) of the Tiny13 IC.
If this still doesn't work, you should also remove the bright LED at the TSOP1738.

Hardware News lesen * Talk * Smarthome und Gadgets
Overclock, Modding und Testberichte * Fanartikel kaufen

Beiträge gesamt: 170945 | Durchschnitt: 20 Postings pro Tag
Registrierung: April 2001 | Dabei seit: 8613 Tagen | Erstellt: 8:41 am 19. Mai 2008

DrJones
offline

OC Newbie
16 Jahre dabei !

AMD Phenom
2500 MHz @ 2500 MHz
48°C mit 1.3 Volt

Hmmm, I don't have any standard LEDs handy... these are all I've got (picked up a bunch from a HK supplier, like US$25 for 700). I'll see about just snipping out LED1 (the one next to the optocoupler) and give that a shot. Although I've tested the LEDs to work on as little as 15mA, since they are high brightness LEDs I suppose it's possible that this one is sinking enough current that the optocoupler doesn't work?

If cutting the first one doesn't get me anywhere I'll go ahead and try removing LED2 as well, but it does seem to work right now (it flashes a few times when I press any remote button for any device... when I use my Logitech Harmony to turn everything on/off at once it goes nuts!). Could it be causing problems even if it appears to be blinking properly?

Thanks again for your help! I love learning, and it's great to have someone to help me along the way ^_^

Beiträge gesamt: 5 | Durchschnitt: 0 Postings pro Tag
Registrierung: Mai 2008 | Dabei seit: 6039 Tagen | Erstellt: 8:49 am 19. Mai 2008

New topic Answer