Ein Ausdruck des Beitrags mit 11 Antworten ergibt bei 3 Antworten pro Seite ca. 4 DIN A4 Seiten. Das entspricht bei 80 g/m² ca. 19.96 Gramm Papier.
-- Veröffentlicht durch ocinside am 19:33 am 2. Okt. 2004
Well, I don't think that it's worth to try the multiplier Pin-Mod with this new CPU as it have the new multi lock (of course the Vcore mod will work).
So (at this time) the only way is to connect also the third L5 bridge to change it to an mobile one ;)
-- Veröffentlicht durch wilwillier am 20:28 am 1. Okt. 2004
tHANX ocinside
thanx u I tried again and discovered that the problem was just the MOBO a7m266-d would still reconnize the CPU`s as NON MP but actually when by mistake I let window start he reconnised both CPU and now works OK. yes yes yes yes....
now that the CPU`s are in MP mod do y think I can try again the interactive-pin Mod ???
and after I will try the L2 cache to 512K .........big hope there........
many thx again
-- Veröffentlicht durch ocinside am 17:51 am 29. Sep. 2004
I think you didn't connect the right points of the 4th L5 bridge.
Because of the new bridge points it could be a little bit confusing how to connect them ...
So be sure that you connect the outer points or scratch the inner points a little bit to get off the isolation of the inner points.
Then you are able to connect the bridges properly ;)
And regarding the multiplier ... sorry, but this doesn't work for the new ones.
-- Veröffentlicht durch wilwillier am 12:13 am 29. Sep. 2004
help :godlike:
I hv bad news 4 axdc2400dkv3c Thorton Core. £49 each
I manage to buy 2 of them to use on MP config on ASUS A7M266-D and unlock extra cache from L2..........BUT I forgot to check the DATE!!!!!!!!.......those r AQYHA0425UPAW .....they being built on 1st week of JULY 2004 ....SUPER LOCKED.....I tried everything.....4th L5 mod NOT WORKING .....L2 mod not working.......cpu socket multiplier by your interactive pin-mod ...NOT WORKING........
U masters hv any idea how to make them work in MP config???
seams no one knows anything about those d..m sh..t
wilwillier@operamail.com london
-- Veröffentlicht durch zenon am 17:39 am 22. Sep. 2004
connecting the pins is what I have done already.
I will make it into a mobile then so I can overclock and make use of my water cooling.
thanks!
(Geändert von zenon um 17:40 am Sep. 22, 2004)
-- Veröffentlicht durch ocinside am 8:25 am 22. Sep. 2004
Yes, you can modify your Barton to a mobile CPU, but I don't think that this helps as you change the multi in windows.
May be there's another way to find out if it's your mobo or CPU.
Try to take out one memory module and then try 200 MHz once again.
Or try to make your CPU runnings as an 200 MHz FSB processor by painting some bridges or connecting some pins.
-- Veröffentlicht durch zenon am 5:42 am 22. Sep. 2004
unfortunately it is a VIA kt-400 mainboard, If I had known the kt-400 chipset had problems running 200MHz FSB before, I nver would have gotten it.:(
will the mobile modification still work on this CPU? (purchased at the start of this summer)
-- Veröffentlicht durch ocinside am 10:13 am 17. Sep. 2004
Hmmm, may be your mainboard recognize that your CPU doesn't start up properly and so set it to the very moderate FSB of 100 MHz.
So please try to lower the multiplier (if your production week is before week 39/2003) and then check it once again with the higher FSB.
-- Veröffentlicht durch zenon am 6:24 am 17. Sep. 2004
I have been successful in overclocking the CPU through my BIOS settings (up to 190+MHz FSB) however my ATI fire GL2 refuses to work with any increases in bus speed.
so I need to run 200MHz FSB with a wire mod to enable the PCI /6 option in my BIOS.
Is that enough information about my CPU? If not, I can rip open my case and tell you the exact production week.
-- Veröffentlicht durch ocinside am 19:10 am 16. Sep. 2004
Hello, please tell us the production week of your barton CPU.
I think that you've already a CPU with the new multi lock :ohwell:
-- Veröffentlicht durch zenon am 7:26 am 16. Sep. 2004
I've tried using the wire mod guide twice!
the 1st time I wired the pins, the 2nd I wired the socket. Results were the same both times:
my 2800+ barton with a stock 166MHz FSB
dropped to 100MHz FSB
instead of upping to a 200MHz FSB
can someone check this wire combination please?
mother board is a soyo dragon ultra with a kt400 chipset
http://www.soyousa.com/products/proddesc.php?id=185
It DOES support 200MHz FSB (goes up to 255actually) RAM is DDR400
Thank You in advance.
[yowza be sure to close babblefish when posting!]
(Geändert von zenon um 7:31 am Sep. 16, 2004)
|